Welcome to MBStarTool.com Sign In or Register
Home - Products - Download & Technical Support - How to calibrate Airmatic Suspension on W211 using Xentry DAS?

How to calibrate Airmatic Suspension on W211 using Xentry DAS?

Photos

How to calibrate Airmatic Suspension on W211 using Xentry DAS?

Description

Simple overview of calibrating my W211 suspension using the inclinometer app on my smartphone instead of Romess tiltmeter. I did not have a picture to calibrate the front suspension, but only the photo of the rear calibration. In the photograph showing the rear voltage value at 2.34 volts, it was confirmed that the rear axle was -1.2 degrees. The original value was close to 3 volts, the rear part of the car was 1 1/2 “lower and the rear axle was -2.8 degrees.

2005 E55 AMG
-Straightened steering wheel by adjusting tie-rod ends (was offset to 1:30 o’clock). Set front toe to 0.5mm toe-in each side using string measurement.
-Calibrated suspension using Xentry DAS. Rear suspension sitting too low causing too much negative camber. Right front suspension lower than left front. Corrected.
-Before: ** = “Axle Inclination” (rear) or “Control Arm Inclination” (front) Left Rear Right Rear Left Front Right Front Camber -2.3 -2.3 -1.3 -1.2 Height 25 3/8” 25 3/8” 26 ½” 25 5/8” ** -2.8 -2.8 +2.6 +2.4
-After: ** = “Axle Inclination” (rear) or “Control Arm Inclination” (front) Left Rear Right Rear Left Front Right Front Camber -1.6 -1.7 -1.1 -1.2 Height 26 3/4” 27” 26 ¼” 26 ½” ** -1.2 -1.2 +3.1 +3.1 Note: Rear inclination measured directly off of drive axles; front inclination measured off of “nubs” on lower control arms. Confirmed voltage values within range, then entered new inclination values into Xentry DAS for programming. Successfully programmed suspension control module.

A brief overview of calibrating the suspension on my W211 using an inclinometer app on my smart phone in lieu of a Romess inclinometer. I did not have a photo of calibrating the front suspension, only a photo of calibrating the rear. In the photo showing the rear voltage value at 2.34 volts, I was under the car confirming the rear axles were at a -1.2 degrees. The original value was close to 3 volts with the rear of the car 1 1/2″ lower and the rear axles were measuring at a -2.8 degrees. 2005 E55 AMG -Straightened steering wheel by adjusting tie-rod ends (was offset to 1:30 o’clock). Set front toe to 0.5mm toe-in each side using string measurement. -Calibrated suspension using Xentry DAS. Rear suspension sitting too low causing too much negative camber. Right front suspension lower than left front. Corrected. -Before: ** = “Axle Inclination” (rear) or “Control Arm Inclination” (front) Left Rear Right Rear Left Front Right Front Camber -2.3 -2.3 -1.3 -1.2 Height 25 3/8” 25 3/8” 26 ½” 25 5/8” ** -2.8 -2.8 +2.6 +2.4 -After: ** = “Axle Inclination” (rear) or “Control Arm Inclination” (front) Left Rear Right Rear Left Front Right Front Camber -1.6 -1.7 -1.1 -1.2 Height 26 3/4” 27” 26 ¼” 26 ½” ** -1.2 -1.2 +3.1 +3.1 Note: Rear inclination measured directly off of drive axles; front inclination measured off of “nubs” on lower control arms. Confirmed voltage values within range, then entered new inclination values into Xentry DAS for programming. Successfully programmed suspension control module.

How to calibrate Airmatic Suspension on W211 using Xentry DAS-1How to calibrate Airmatic Suspension on W211 using Xentry DAS-3How to calibrate Airmatic Suspension on W211 using Xentry DAS-2How to calibrate Airmatic Suspension on W211 using Xentry DAS-4How to calibrate Airmatic Suspension on W211 using Xentry DAS-5

 

 

 

As you can see, Xentry DAS calibrate Airmatic Suspension on W211 successfully.

Write a Review
* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Detail:
*Verification Code:
      4120    No right? Get a new Verification Code
 
Tell us what you think about this item and share your opinions with other people. Please make sure your review focuses only on this item. All reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.
After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).
Please Sign In first if you want to later edit or manage reviews uploaded by yourself.
Bookmark It